Keith carpenter Posted June 14, 2020 Author Report Share Posted June 14, 2020 i have noticed that when spa gets up to the set temp the circulating pump shuts down then there is a quick flo error then that disappears and the spa displays just the temp of the water i thought the circulating pump should run 24/7 ? when looking around the control panel there was a temp sensor just hanging from the box,i have since found out it should be clipped to the heater tube. it has never been clipped to the tube since i have owned it. Quote Link to comment Share on other sites More sharing options...
Keith carpenter Posted June 14, 2020 Author Report Share Posted June 14, 2020 i’ve noticed a jumper on J10 which says enable pump 3, but i do not have 3 pumps only the circulation pump & a 2 speed pump, i wonder if the previous owner had work done on this spa & used a similar board & made it fit ? Quote Link to comment Share on other sites More sharing options...
RDspaguy Posted June 14, 2020 Report Share Posted June 14, 2020 For 24 hour circ pump j6 needs a jumper on both pins according to the info @CanadianSpaTech sent. Your sensor needs to be installed properly but is not related to the flo error. Quote Link to comment Share on other sites More sharing options...
RDspaguy Posted June 14, 2020 Report Share Posted June 14, 2020 Your board is also set for 60hz. Does your area have 50hz electrical? There is some printing on the board beneath the controller plug that is about the jumpers but I can't see all of it. Quote Link to comment Share on other sites More sharing options...
Keith carpenter Posted June 14, 2020 Author Report Share Posted June 14, 2020 Hi, I believe the uk is 50hz, can it be changed, if so what do I have to alter ? Quote Link to comment Share on other sites More sharing options...
CanadianSpaTech Posted June 14, 2020 Report Share Posted June 14, 2020 1 hour ago, RDspaguy said: For 24 hour circ pump j6 needs a jumper on both pins!!!!!!!!!!!!! according to the info @CanadianSpaTech sent. Oh sure blame the Canadian...lol 1 Quote Link to comment Share on other sites More sharing options...
RDspaguy Posted June 14, 2020 Report Share Posted June 14, 2020 To the right of the pressure switch plug is the bank of jumpers. The one on the bottom, j25, is a 3 pin and is labeled 50hz on the left and 60hz on the right. Move it over so it connects the 2 leftmost pins. Quote Link to comment Share on other sites More sharing options...
RDspaguy Posted June 14, 2020 Report Share Posted June 14, 2020 Make sure power is off when you do this. Quote Link to comment Share on other sites More sharing options...
CanadianSpaTech Posted June 14, 2020 Report Share Posted June 14, 2020 1 hour ago, RDspaguy said: For 24 hour circ pump j6 needs a jumper on both pins @RDspaguy Wonder if we will ever find out Quote Link to comment Share on other sites More sharing options...
RDspaguy Posted June 14, 2020 Report Share Posted June 14, 2020 Idunno. This board has j6 labelled "interlock option". I am beginning to think we are looking at a hodgepodge system with the wrong board. It doesn't even have the right hz setting. We may never get to the bottom of this one. Quote Link to comment Share on other sites More sharing options...
CanadianSpaTech Posted June 14, 2020 Report Share Posted June 14, 2020 1 hour ago, RDspaguy said: This board has j6 labelled "interlock option" Have to go by the white Balboa sticker on the board # 54126 MPN: 54126 Product Attributes Quick Find Code: 31009 Brand: Balboa Make & Model: 54126 Width (cm): 24 Height (cm): 18 Pump 1: Single or dual speed Pump 2: Single (or dual speed with no blower) (J10) Pump 3: N/A Circulation Pump: Optional (J6) Air Blower: Yes Heater: Yes Light option: 12 volt or 230 volt Topsides Compatible: VL Range (J7 Switch to Deluxe) Please note all Hot tub Parts sold are UK Spec, which means designed for 230 V at 50Hz 1 Quote Link to comment Share on other sites More sharing options...
Keith carpenter Posted June 15, 2020 Author Report Share Posted June 15, 2020 Right, I have changed jumper to 50hz also taken the jumper from j24 (orp enable )& put it on j6, I’ll see what happens now & let you know..... Fingers crossed Quote Link to comment Share on other sites More sharing options...
Keith carpenter Posted June 15, 2020 Author Report Share Posted June 15, 2020 Hi guys, I think between you, you have given me sound advice I have followed your suggestions i:e changed over to 50hz and removed jumper from J24 & put it on J6, the circulation pump is running As it should now No flo errors. I can’t thank you enough for your advice. Now I can enjoy the spa well done Quote Link to comment Share on other sites More sharing options...
RDspaguy Posted June 15, 2020 Report Share Posted June 15, 2020 👍 1 Quote Link to comment Share on other sites More sharing options...
CanadianSpaTech Posted June 15, 2020 Report Share Posted June 15, 2020 👍👍⭐ 1 Quote Link to comment Share on other sites More sharing options...
CanadianSpaTech Posted June 15, 2020 Report Share Posted June 15, 2020 Canada and U.S. saving the Brits...again 😄 Quote Link to comment Share on other sites More sharing options...
Keith carpenter Posted June 15, 2020 Author Report Share Posted June 15, 2020 And it is appreciated,🤩 Quote Link to comment Share on other sites More sharing options...
RDspaguy Posted June 15, 2020 Report Share Posted June 15, 2020 None of us were even alive then. Just can't let them forget, can you? Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.dc5a6170fa916412670749ff27e20047.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.