HSFan

Will test. Thanks

Yes. 124 at both green/black and green/white. What should I test next? thankS!

Hope you’re well. Thanks for advice and will check voltage. Ive attached description of purchased heater element and has auto reset.

Hello again, my new heater not getting water hot. It is set at 103 but feels like 80. Circ pump is working and see bubbles in hot tub. All breakers are in correct position. Should both green and red LED on board be on? Any assistance appreciated.

Im back and you were right! 🤨Garage breaker blew 3 times since last message. (But enjoyed incident free tubbing several times) I checked breaker visually and looked all ok. Going to replace breaker with Eaton 230250 quad $22. Picture shows breaker slightly popped. Will keep u posted.

Will do. I have box outside by hot tub with gfi Breakers connected to breaker box in garage. The garage breakers are original from old tub. I’ll open it up to see if any issues. Thx for headsup!

No problem. Humor best medicine👍🏼 Well woke up and tub at 101 degrees, ready light on. Turn pump 1 on and ran for 20 mins. Turn both pumps on and been running for past 30 mins!😁 Hopefully stays good all day and more! 🤞 Thanks for all your expert guidance and patience getting me thru this!

Heater and pumps working. I turned heater to 80 and ready light turned on.👍🏼 Ran pump 1 for 5 mins and turned on pump 2. Both ran for 8 mins and breaker blew. 🤔

No I wudnt make this stuff up. Believe me I’d rather be sitting in this hot tub with a ice cold beer. I got 3 teenagers that ask me everyday for past 2 weeks “dad is the hot tub fixed?” So I really appreciate your patience! Let me try now....

Main breaker in garage goes off when wavemaster runs for 10 mins. Any suggestions? Thanks!

Also the new heater is not working either. I took temp at 5am today and read 65. I checked back at 10am and still same temp. Bubbles are flowing from bottom drain after new circ pump was installed. 😩

The circ pump and heater install was fairly straightforward and ensured I didn’t touch anything else. Would air block be cause? Does the ready light need to be on for pumps to work?

Yes I do. I’ll test for voltage. Odd both pumps were working a day ago. Thanks much again!

CB are on. What shud I try next? Hanks!

Power light is on. Ready light is off. No blinking. As I push Jet button 1 or button 2 I hear a click and nothing turns on. I looked at board and lim and heater light is on. The sound I think is coming behind plate where relays are. Any Help is appreciated. Thx

Hi again - I finished the circ pump install and bubbles are now flowing But now wave pumps not turning on. Got any advice? Thanks as usual!

Hello again Guru - I was hoping it was air block issue to save some $ but I have ordered Laing circ pump and new ozone hose because mine has some debris in it. Appreciate your expert advice and let you know outcome.👍🏼

Hi again, I thought I’d try and bleed the hose to circ pump again and ran a little longer. Connected back up and fired up breaker - no flashing light😁🤔. But still no bubbles from center. If circ pump is working does it get warm as mentioned in earlier message? Is no bubbles mean something else not working? thanks for guidance!

Thanks Spa Guru!

I bled both earlier with no change. I was going to disconnect hoses from circ pump, open circ pump to see if moving for a few seconds to see if functional. Would that be a good next step? thanks for your advice!

Hi - I just installed new heater on my workhorse Landmark. As I turned on breakers circ pump making started weird noise I never heard before. I can see water slowly going thru tubes for a few minutes and then red lights would flash start flashing. I flipped off breakers and this time red light stayed solid. There were no bubbles. Jet 1 was running but shut off in a few minutes and red lights started to flash. Is this a circ pump issue? Any advice would be appreciated? Thanks