dansdad
-
Posts
9 -
Joined
-
Last visited
Posts posted by dansdad
-
-
I want to test my levels in my pool and spa. I have a salt kit for my pool but I would like to get a kit for the spa and I dont do well with strips. I normally take a sample to leslies pool supply but I would like to learn to do it myself. What do You suggest??....Thanks Dave
-
DAve,
The heater will automatically run to a presite temp of 100 degrees, even when you cannot adjust the heater,,, i am leaning toward a problem with the topside control unfortunately...
Thanks for the answerI cannot see the screen so I dont know the temp...now I do. I guess I knew it was the controls just hoping for something else. Thanks for responding....Dave
-
No swivels exist for the Navigator. It should turn off steps in both directions to eliminate hose coiling. Your problem likely exists in one of the following areas:
1. One of the pods (long white plastic piece on each side) is very loose & causing it to turn only in one direction.
2. Main gearbox is stuck turning only one direction.
3. Upper gear is stuck turning only one direction.
A simple test you can use to help narrow it down is to make sure the pump is on and that you have correct suction to the Navigator. Without proper suction, the cleaner won't operate at the proper speed. Use the suction gauge that came with the cleaner to verify correct suction, if you still have it. Lift the cleaner by the hose until the head of the cleaner is off the floor, but still submerged completely. The head of the cleaner should rotate on the end of the hose - turn left, stop turning, turn right, stop turning, turn left, etc. and should repeat this pattern. If it's not turning, or if it only rotates in one direction, the internal gearbox is the most likely problem. You can download an owner's manual for the Navigator here... Hayward Pool Products
Thanks much I have 2 new flappers I will install and I will check it out as you say. Thanks Again..Dave
-
Dave
What year is your Chairman... You say it lights up do any of the the buttons work on the topside... does pump 1 work, If you press pump 2 does it work, does the light buttone work and does the temp button work, if everything works but the one pump button, it may be another issue,,,,,
My Chairman is a 2003. The one button opposite the top panel controls 1 pump and it works. Pump comes on no problem. The heater comes on but the heating light on the panel doesnt come on. When I say the lights on the panel come on its the small light where you can see that the panel is connected. So the panel is getting power to light up...but wont operate either pump or the heater. Almost as if the heater is bypassing the panel and going right to the heater. Confusing I know......Thank you for your input...Dave
-
I have a navigator and it works fine but keeps getting twisted hoses. The cleaner doesnt turn very easily causing the twists. Are there any swivels for 1-1/4 hose or is it the cleaner>>>> Thanks Dave
-
I have a D1 Chairman and the upper control panel lights up but wont start the pump. Am I stuck with a 350.00 new panel??? Thanks Dave
-
My Dimension one Chairman is leaking what appears to be under one of the filter housing and near the hose than runs under it. all the foam is soaking wet and I dont know what usually causes this the spa is 7 years old, but we love it. Thanks for any input...Dave Gale
-
My Dimension One spa heater went out and I replaced it...didnt get hot , called the circulating pump distributor and he asked it I bled the line. wwweeeeellll like no , so I did and where the heating water is supposed to come out , bubbles are there but not the force of heated water. Please help.....the spa is only 51 degrees. Thank You..... Merry Christmas!!! Dave Gale
Testing Equip.
in Hot Tub Water Chemistry
Posted
I did not mention I use a vision cartridge, and an ozinator. Does this matter? Thanks Dave