Search the Community
Showing results for tags '2005'.
Good morning, all! My husband and I have been looking to purchase a hot tub for about a year now, but simply cannot bring ourselves to spend $6k+ on a brand new tub. I was poking around online yesterday and happened to find a used 2005 Sundance Cadence hot tub that a woman was giving away for free, as long as we haul. We went to check it out same day and loved it- it's a great tub and looked well maintained. We have to figure out how to move it, so I started calling a few local hot tub haulers. The one who got back to me said he would politely decline the job as the Sundance tubs from that time period are made with a type of wood that often rots out from underneath. He said the bottom of the tub may detach from the rest of it when we try to move it onto its side. My husband is very handy and it doesn't phase him that he may need to rebuild some of the base, but it scared me a bit. Has anybody dealt with this? Is this really a very common issue with the Sundance tubs? We'll now be moving it ourselves so we're trying to figure out those logistics, too. Thank you.
Hi, New to the forum and have a question for you all. My hot tub trips the 20 Amp GFCI when I turn the pumps on sporradically. Most typically noted on jets 2, and if they do come on then I turn them off and back on it will trip. Once on they run strong for 30 + minutes. So, powering on pump 1, then pump 2, may work fine, however if I turn pump 2 off it trips the breaker when I turn it back on. I disconnected pump 2 from the IQ2020 and pump one had noe problems. My best guess is its the capacitor, but newb to hot tubs. The hotsprings store said that you cannot buy a capacitor alone, and would need to buy a motor. They also offered to come check it out for a $200 service call. Any advice would be appreciated!
Hello - We have a Sundance 850 series 'Marin' hot tub that had a few issues in the past (see post: http://www.poolspaforum.com/forum/index.php?showtopic=26961&st=0) We resolved our previous problem by replacing the circuit board and all of the filters. After we did this in the spring last year, the hot tub worked for about 4-5 months but then just quit working. It gives us the awful "Watchdog" (----) error again. We did some tests and think the circuit board is bad again. So, recently we actually paid a Sundance hot tub tech to come out to diagnose the problem, as we did not want to keep replacing the expensive circuit board every 4-5 months just to get it to work. We figured there must be some underlying issue corrupting the boards. The tech determined that he wasn't really sure what the problem was but thought that we could start by replacing the circuit board and topside and then maybe the remote topside too if that didn't work. I gave him the old board we took out a few years ago (yes, I kept it!) in case that helped him diagnose and he said they both have the same issue. FYI - He did say that he thought one little spot in the topside might be getting a little warm. Also, when he was there, the hot tub was able to start ONCE, but then he couldn't get it to start again. I really don't want to pay to replace of those pieces as a trial and error type "solution" to the problem. He said the temp sensor is good. He looked at the capacitors on both boards, we kept the old circuit board too, and said they were not swollen and look fine. The tech was also unable to read the history/memory to get any other clues as to what could be the problem. So much for hiring someone to tell us what was wrong...ughh! (FYI - Also, in our previous problem - see link above-, we also had the breaker tripping and the tech that just came out said that was due to the ozenator so he just disconnected it since it's an option feature anyway and not required to make the spa work.) Before we buy a new circuit board or any other parts, do you have any idea if just replacing the circuit board will make it work? If it is going to cost A LOT to repair (we plan on doing the work ourselves) in parts, then we may just get rid of the tub completely. I've also seen some refurbished circuit boards online. Has anyone used a refurb board and do they work ok? I noticed some come with the Eprom and some don't. (I was told you can install your current Eprom into the refurb board fairly painlessly.) Any experience with this? THANK YOU THANK YOU THANK YOU for any help, advice, experience, suggestions you can offer! Hot Tub: Sundance Marin 850 Series (year 2005) Circuit Board Part #: 6600-092 Eprom: Rev 9.50B