Jump to content

Search the Community

Showing results for tags 'landmark'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Hot Tubs & Spas
    • Portable Hot Tubs & Spas
    • Inflatable Hot Tubs
  • Inground, Fiberglass and Aboveground Swimming Pools
    • All Swimming Pools Types
  • Swim Spas & Exercise Pools
    • Swim Spas & Exercise Pools
  • Pool/Spa Water Care
  • Swim Spas & Exercise Pools
  • Pool/Spa Water Care
    • Hot Tub Water Chemistry
    • Swimming Pool Water Chemistry

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Location


Interests

Found 4 results

  1. Hi folks Apologies for the *long* post - but could use some help. I have been troubleshooting a blinking red-light problem with my Hotspring Landmark (2000 year model). I have always had a problem after refilling this spa (everytime after a refill if I flipped both breakers on - the blinking red light would turn-on) - the way I would resolve this is by turning the 20A breaker on, then running jets for at least 30 mins to an hour and then turning the 30A breaker on. Sometimes it would take 2 - 3 times of doing this - but it usually worked. Then I refilled last month and noticed one of my jet-pumps leaking - I had a local service person come take it out - had to drain the freshly filled water and replace the wet seal and impeller on it. When he came back to re-install it, he accidentally broke the little black nozzle off the right-angle elbow attached to the circulation pump (that connects to the bleeder hose) - so he replaced the elbow and put a brass barbed fitting in it to connect to the hose. After this I refilled the tub and had my blinking light problem again - and noticed that I wasn't seeing too many bubbles through the bottom drain (they have been low in general) - so did the following troubleshooting: 1) removed the filter and tried - didn't work 2) removed the venturi injector tubing from ozonator check valve -- water comes out of this unless I started Jet-pump-1 at which point the water gets sucked back into the injector.. 3) removed the intake hose from the circulation pump and connected it back in to remove any airlock -- started the jets and 10 minutes later started the 30A breaker - did not trip this time.. However few hours later the red-light was flashing again.. 4) This time I took out the circulation pump (thinking it might have scale deposits inside or something broken) - plugged the hoses with caps so I didn't have to drain and dismantled the pump wet-end (its a silentflo 5000) - pump looked great - no scale / no deposits / no broken parts.. I took it to my local store and the tech there did a dry test and said the circ-pump looked ok to him. 5) Since I had the circ. pump removed - I decided to check the watakins no-fault heater for clogs too, so I removed it; opened the end caps and it's clean as well; resistance was ~9 ohms. 6) So put everything back together - turned on the the 20A breaker and got a good-stream of bubbles initially but they trickled back to a low stream very quickly after that. This time around after disconnecting the injector tubing at the ozone check valve, water still leaked out even after turning on the jet pump - so something was different than before. 7) Turned on the 30A breaker - didn't get the blinking light - left it running -- of course few hours later the blinking red light was back!! So I am still thinking it's my circ. pump - just ordered a new Laing E5 repalcement - but in the meantime - I am wondering if something else is going on.. Any suggestions from anyone? Thanks mrcotton73..
  2. Hello everyone! Seems like this is the spa place to be. I just recently got a beautiful Landmark S for free. Happened to be in my own neighborhood. The thing is immaculate, but does have a small leak in one of the upper jets. So I got it for free, built a deck to put it on and began to run electric. Got it all the way out to the tub and THEN found out it needs a special subpanel. The original owner doesnt want me to have his because "it will leave screw holes in the deck". Watkins wants $500 for one. So off to eBay I guess unless one of you have a better suggestion. From everything I can tell, I need the old 31578 (now Eaton 301755). Any suggestions on other part numbers, better costs, etc? Thanks in advance! Bob
  3. Ok so I installed a new/used Watkins 5002 circ pump yesterday in my spa and it works great, but the spa now gets way to hot (around 115F) when I checked it and turned it off when I turn the thermostat knob you can here the relay clicking iv tried to let it sit un-powered for an hour or so and turn it back on the but the pump immediately goes into its second speed as if it need to heat up the pool more but the pool is still really hot. Any help will be greatly appreciated.
  4. I have a Hot Springs Landmark hot tub, bought new in 2002. Not getting power to the heater. Well, first the heater relay board shorted out and blew. I bought a new heater board and installed it today, but the heater is still not working. The no fault heater seems ok, tested it with meter and got about 10 ohms between wires. The circulation pump is running. On the main board the green light is on and the red light is on. Still getting no voltage to the heater though. Could the new board be bad or maybe a relay on main board. Anyone have any ideas on what could be the problem. Thanks.
×
×
  • Create New...