Jump to content

Search the Community

Showing results for tags 'SnS'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Hot Tubs & Spas
    • Portable Hot Tubs & Spas
    • Inflatable Hot Tubs
  • Inground, Fiberglass and Aboveground Swimming Pools
    • All Swimming Pools Types
  • Swim Spas & Exercise Pools
    • Swim Spas & Exercise Pools
  • Pool/Spa Water Care
  • Swim Spas & Exercise Pools
  • Pool/Spa Water Care
    • Hot Tub Water Chemistry
    • Swimming Pool Water Chemistry

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Location


Interests

Found 3 results

  1. I'm having an OHH code on my beachcomber hot tub I just replaced the smaller pump as the last one burned out. I filled from the filter housing, opened the bleed screw and drained all the air through there, everything seemed okay last night but when I checked it this morning it was still cold and there was a SNB code I pulled the sensor out (lots of water no air) and also unplugged it and sprayed with electrical contact cleaner Now instead of a SNB code I'm getting the OHH as soon as I turn on the breaker even if it has sat for a few minutes I also tried unplugging the b sensor and there was still an OHH code right away. Maybe needed more time to reset though ? Hoping it's not a circuit board. Don't really wanna keep throwing parts at it. Everything was working fine before the pump burnt out Any help appreciated ! Thanks!
  2. Hi, I have a coast spa running a Balboa system. I keep getting the " SnS " error code and the spa shuts down. (its flashing) What is thte fix for that? When I see it in that state as soon as a press the temp up or down button the spa comes back and it's happy. If I just leave it and ignore it. the spa cools down ....... Any help you can offer is appericated! Cheers' Dave
  3. A few year old (4-5?) legends series lsx masterspas tub. It is throwing a few different codes, SnS, dr, then dry (and sometimes Ohh) I suspect these are all related, maybe a non working circ. pump? I have tried to bleed the circ pump, I have checked the head of the circ pump for ease of propeller spinning and no clog. I have turned power off for 5 minutes after each attempt, still not good. (I also started with trying to run without filters, which are clean, just in case was a simple flow issue) Symptoms are that it is not heating. All three pumps seems to work, 2 at both of their speeds, and pump three at its only speed. It does, sometimes, rapidly raise the detected temp. up to the 118 shut off limit, but not always. Water temp is in the 65-75 range right now, as it's not been working for a few days, and it's getting into the 40's-50's at night up here in New England. Upon opening the front, there is a small pump maid by "Laing" that says circ. pump, and I don't seem to see this running. But truthfully, I don't remember if my circ. pump ever ran on its own? Never really paid attention. It does connect directly to the heater tube tho, so being that the dr and dry codes mean not enough water in the heater tube, am I correct in assuming that it is not pushing water into the heater and should start by replacing this? I'd hate to replace it, to find that it's a sensor or something, since the other two codes point to them as well. .? Please help, I am unemployed and can't afford serious costly service reps, but my wife has a bad back and needs this tub working. Thanks in advance, John
×
×
  • Create New...