cranbiz
Members-
Posts
685 -
Joined
-
Last visited
-
Days Won
51
Everything posted by cranbiz
-
Aquaterra Circulation Pump Noise Level
cranbiz replied to jbtremble's topic in Portable Hot Tubs & Spas
The pump is supposed to run on a schedule set by you. It can be 2x2hours 2x4hours, 2x6hours, 2x8hours or continuous. Some tubs have a different schedule but most have a way to program the filter cycles. -
Another thought is it could be the flow switch/flow sensor.
-
OH can be a couple of things. It usually happens when the temperature probe senses the water is above the programmed limit. Things that cause this is poor flow thru the heater or a bad high limit sensor. If you have a circulation pump, that could be bad, it's not uncommon. The first thing to do is pull the filter and run the tub without it. A dirty filter will absolutely cause poor flow and an overheat condition. With a multimeter, read the resistance of the high limit sensor. It should be in the 10,000 ohm range at room temperature.
-
I can't find anything on error HA. Your video doesn't work either. You don't need to keep repeat posting this post. Not everyone here that can help sits by the computer waiting for an issue to help with. We usually ask for pictures and that you start your own post. Is it doing anything? Pump runs, water flows,? Is the water getting warm/hot at all? Is there a removable filter? If so, remove it and see what happens. Check to see is all plugs are tight. If you can unplug and reconnect the plugs for the pump and sensors. You may have had one come loose. If nothing works, I suspect that it's not something you are not understanding but a genuine defect that requires warranty service. Now that is probably going to be impossible to get. Can you pack it back up and return it to Wayfair? Unfortunately, inflatable hot tub manufacturers are less than responsive on problems. Most are Chinese companies making them for someone else to put a label on. Many are considered unrepairable by the manufacturer.
-
Don't use strips. They are hard to read and inaccurate. Like @CanadianSpaTechsaid, get a Taylor kit K-2106 for Bromine if you plan to stay with Bromine.
-
Generally you want your hardness in the 200ppm range. I would get it down to 200ppm and then see what happens with keeping levels where they should be.
-
Check the heater. Make sure the element is not touching the tube. Also test the high limit sensor.
-
Hotspring Vanguard spa will not start up
cranbiz replied to hyperman's topic in Portable Hot Tubs & Spas
Air lock is easy. At the pump, crack the coupling and keep it cracked open until water flows freely. -
Balboa EL2001 Mach 3 Board Information
cranbiz replied to caldog20's topic in Portable Hot Tubs & Spas
Why would anyone take offense? The whole premise of this board is to help each other fix their tubs. Some people have the ability to fully DIY, some don't. Go for it and let us know how you make out. -
There are 2 fuses to check. The 1/8th amp (F2) and the 3 amp (F5) fuses.
-
Balboa EL2001 Mach 3 Board Information
cranbiz replied to caldog20's topic in Portable Hot Tubs & Spas
I see a heater relay that looks suspect. If the relay is shorted, that can easily cause an overheat situation. Relays are around $15 each. I would test the 2 heater relays and replace them if bad. -
Sundance Altamar new cover suggestions.
cranbiz replied to Bill Mac's topic in Portable Hot Tubs & Spas
The Cover Guy is a popular suggestion here. -
OK, 110V tub wiring. Heater light never comes on? Is the display OK? Any codes, messages or dashes on it if it's ok?
-
Draining and closing Sundance Marin 880 series for the summer
cranbiz replied to Ben M's topic in Portable Hot Tubs & Spas
External air source. You can use a shop vac that has a blower function or an air compressor. -
As for the heater, when the tub is calling for heat, measure the voltage on the heater terminals. Depending on your setup, you should have either 120V or 240V across the terminals when the tub wants heat. If you do have voltage, it's a bad heater. If you don't, it's most likely a bad relay. Looking at the board, do you have any burn marks on it? Upload pictures of your control board and wiring diagram.
-
Draining and closing Sundance Marin 880 series for the summer
cranbiz replied to Ben M's topic in Portable Hot Tubs & Spas
You will have stagnant water in the lines. Unless you blow out every jet and line, you can't avoid it. -
If it's new, it should be under warranty. I would call your dealer and ask the service department and schedule a visit if they can't walk you through a fix. My dealer walked me though an issue when mine was new over the phone.
-
What's the make and model of your electrical panel. Usually there is a label with that info on it and also compatible breakers. Post that up. Seimans makes several styles of panels as well as Square D, C-H, Murray, etc. Depending on the panel, the breakers from other companies may work. I can tell you that certain Seimans breakers work in the Square D Homeline panel but others will not but work in Square D QO panels. Same with Seimans panels.
-
It should work with the pack. It just won't do anything.
-
Why is the hot tub pausing like this?
cranbiz replied to JamieCole's topic in Portable Hot Tubs & Spas
Attachments unavailable. -
Edges of hot tub off the ground??
cranbiz replied to Charliesal7's topic in Portable Hot Tubs & Spas
Is anyone else noticing that there are a bunch of new posters with the same exact posting template, offering questionable advice and always has a link to their services? -
Start a new thread, this one is over 8 years old. In that new thread, describe your problem in detail and post up pictures of your spa pack insides with any DIP switches, the wiring diagram usually found on the inside of the cover and of the equipment area. With that info, we should be able to help you out.
-
Aeration will cause pH to rise. Make sure you get your TA correct before trying to adjust the pH.