Jump to content

arnspa

Members
  • Posts

    123
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by arnspa

  1. Query: Ive not seen these offered. We recently replaced with a four section cover, so don't need one now.. But wish to ask: Is this rolled up by hand? Can it be managed from one side? Where can one get the end support? Would it also fit a 12 ft spa?
  2. We got delivery in about 7 weeks. Learned that one reason for possible delay is that the cover was made in Mexico and shipped from San Diego. I might add the cover is great quality, superior to our last. But also an inch thicker, heavier than last. I should have tried to get a lighter one adequate to the California Bay peninsula. It might have been cheaper and easier to manage raining and lowering.
  3. We need to replace the cover on our 2008 MasterSpa H2X Swim Spa. It is 8x12 ft, two piece. We're just south of San Francisco (no snow). Some places say expect as long as 4 months for delivery. Any recommendations for quality cover and maybe quicker delivery welcome.
  4. Repainted Hunter Green, gloss with new safety strips for the steps. Much better than redoing the varnish every year,
  5. DON'T REPLACE JUST ONE OF THE GASKETS Last week I noticed we had water leaking again. Taking off the tub surround and the extra insulation I put in I discovered the other side of the heater was leaking. I ordered another gasket before taking it apart as I expected to lose some water when I took off the split clamp. I closed the three gate valves to the heater and pumps and shut off the power. The gasket arrived today. When I took off the clamp, sure enough, water was leaking out, not great force but enough to prompt me to work quickly to replace the old gasket with the new and to put the split nut back on and to tighten it. Perfecto. I turned the power on and briefly ran the pumps; no leaks. All together about three inches of water was lost from the time it started leaking to finishing the fix. The gaskets cost $2.90. Sure wish I had bought two and replaced them both. Now, YOU will know.
  6. Ingenious! When we got our H2X 12 years ago, we also got rooftop solar that has kept the bills low.
  7. OOPS! I didnt know how the Split Nut pictured above works. I thought it was just a split clamp and after spending lots of time trying to align the the flange on the heater and the pipe I finally realized the pipe is threaded and the split nut is used to draw them together. Eureka! Just put the new gasket on end of pipe, then put nut on with the screws not yet fully tight and start turning nut to pull the pipe and heater together. Once they are lined up close you can tighten the screws in the split nut and turn it to make it all tight. I never needed to spend all that effort using a collection of offset Phillips to get it off. I just needed to unscrew it so the screws would be accessible at the top. A strap wrench would help for this. We live, we learn. I added some 1 ½ inch foam insulation (foil on inside) to boost the ½ inch in the tub surround. I had many loose plastic pieces from the surround and used Gorilla building adhesive, weighted down overnight. BUT the adhesive stuck to the plastic fine but not well to back on the surround. With more screws got it all back together. (Third pic shows mid process of gluing back the plastic pieces to the surround. Anyone know a better adhesive than the Gorilla tube stuff I used?)
  8. Spa Access: Twelve years ago I built steps to access the side of our H2X. They are easily skidded away if access to panels is needed, plus seem perfect for enter at side away from the sloping seats at end. After years of new varnish every summer I plan to paint it green this year.
  9. Our H2X is at least 80 feet from our main electric service box. I think this too far to rely on the copper ground rod at the main service, and so I drove a copper ground at the service switch close to the tub. I wish I had tied it into the rebar in the concrete pad, but didn't think of that until after delivery.
  10. Other projects and worry what I might find kept me from this problem. After almost a year out of service I removed the plastic end at the head of the tub and easily found the leak. Water dripping from the Heater Split Nut due to a failed gasket. After a little trouble getting the screws out* I found the part at MasterSpaParts. On query Jenni told me that a replacement split nut (about $11) did not come with the gasket. It is separate for $2.90. It has been ordered and I expect to be back in tub this week. Picture shows the split nut and where it attaches to the Heater. I wish I had done this 16 months ago. Note: The white rectangular box at the left is a valve to close the water return line to the heater. It only partially worked, slowing down the flow after I removed the split nut but not stopping it. Perhaps a gasket there was also shot. So a good thing that mostly all of the water had leaked out already. * The screws in the split nut were facing down rather than up, requiring offset Phillips drivers to remove them. I will replace them facing down, as they are on the split nut at the other end of the Heater. [OOPS! This idea shows my then confusion about how the split nut works. See fix below.]
  11. Thank you for your Reply. A MasterSpa H2X is 8'x12', 1300 gallon. I will try to see what I can behind the panels. Unfortunately 2 sides are tight against walls, and everything behind the panels is sprayed with foam. But the leak MAY be obvious if I look for it on the 2 available sides. Anyone have maintenance folk deal with these issues?
  12. We have a 2008 H2X SwimSpa we have much enjoyed but it is now leaking. Any suggestions to find leaks, fix, or get help?
  13. After fixing my problem with broken suction covers, I now have many jets not working in my 2008 H2X swim spa. Leaf debris, I suspect. Any tips on how to fix this?
  14. WHAT? No One can recommend a supplier for a new tub cover? MERCY!
  15. For a round 77 inch hot tub we need a new cover in Berkeley, CA. Recommendations please.
  16. I think I got just what you recommend. Cost $1,100. Our old cover, 2008, was well worn out. Another post here told of my efforts to save it 3 yrs ago. Now the vinyl was shot, plus one quarter was water laden and very heavy. The new design is much superior. Though it doesn't have a nylon mesh underside. I think that was a drawback on the original.
  17. Our daughters have recent got a large 110 hot tub and installed solar at their house in Berkeley, CA. What sort of timer do they need to take optimum advantage of the PGE time of use billing?
  18. Any recommendations for where to find a replacement cover for our MasterSpa H2X (8 x 12 ft)?
  19. Just a few months later. It still looks great. Gorilla brand is a super heavy duct tape. It comes in two widths, wide and wider. In black only I think and costs much more than the cheap stuff. Because the seams are on the edges covered by the vinyl, and very tight, I really do expect the seal to last as long as the original did. Concern for the vacuum seal may be overstated. Any vacuum was broken with the first tiny hole that came years ago. My guess is that the mechanical seal can be better than tape but largely dictated on manufacturing efficiency. Commercial mailers seal their plastic packages with heat rather than tape. Quicker, and cheaper for large production. Tyvek tape? That may be smart. Haven't used it. Glad to hear from others.
  20. Below I show Before and After photos of my DIY to replace the plastic surround of the insulation in the cover of our MasterSpa 2X Crosstrainer (12x8') . The black plastic was showing cracks long ago and I should have got to it at once, especially because the side I couldn't see, the top side, was much worse that what I could see on the bottom. I bought a roll of 10x25 ft 6mil black plastic at Lowes's ($25), and a roll of 3 " Gorilla duct tape ($14). I have more photos and will try later to post a How To here. I have lots of tips to make this easier. As my father enjoyed saying, Don't do anything the first time. Check with me before you begin this, The replacement costs for the covers are $1200. I spent $40 and a weekend. This will probably last for for the remaining life of the cover.
  21. After 6 years the black plastic surrounding the styrofoam insulation in our Master Spa cover is disintegrating. Taking it apart I see that each piece of syrofoam is contained in a black plastic bag of sorts. Does anyong know how to get replacements for these bags? Alternately I can just put plastic sheeting around it but the bag would work better. Any help? Thanks.
  22. clyde, I would guess you've already done something about this. And I would guess that Brian above is a spammer. You may have nearby electrical motor rebuilders that can help with problems like this. It may need just new brushes or brushes and minor dressing of the armature. This may be a lot less than $900 for a new/rebuilt motor.
  23. One week and no reply? Have our pros never seen this before? I might add the water was clear (1300 gals), the pH was very low.
  24. Our visitor did not wash the filters in our Masterspa H2X for many months. When I came to change them they were coated with a sort of green gel like stuff, see photo. This later dried to dry powder. Anyone know what causes this?
×
×
  • Create New...