AlienZen

I used the spa last night. Today I unplugged the spa, drained it, and filled it. After plugging it back in, the circ pump turned on, and the heater seems to be working. (It feels warmer than the rest of the piping in the pump area) But, the main pump and light switch does not work. It all worked fine last night. Is there any sort of reset I don't see? Is it normal for the panel to stop working so suddenly? Any suggestions of anything I should look for? Nothing is unplugged. Thanks, Mike

Okay, first off, I got the serial number, and it turns out this isn't a Tiger River Bengal. It's a 92/93 Tiger River Manora. The leak can be seen here: http://farm2.static.flickr.com/1025/143619...d1d2f16a4_o.jpg About 1/4 of the circumference of the flexible hose where it connects to the jet. Now, what is the best way of sealing this? I can't just cut off the nipple and replace it. Whats the best tip for getting the flexible pvc sealed back into the coupling? Thanks again, you all have been very helpful! Mike

Yea it sucks, If you have the new jet figure out where you need to cut the pipe or tubing and just do that so you don't have to clean off all the foam except where your going to re-glue. I also would be around a 1 or 2 hour repair. We are seriously underpair...LOL But I to pay for someone else to work on my car because I hate it. I payed someone to reroof my house even though i've done the last 2 myself. It's funny how we get that way. I use a utility knife to cut foam being carefull not to cut the tubbing your trying to clean. I found the leak, and started a new thread to discuss the repair. The new thread is called "Found the leak, now what?" Thanks to all

Thanks for the response. Yes, I looked around at several different producers of these products, and all of them claim to be the greatest thing since sliced bread. I was hoping for some feedback from those not affiliated with the product as to whether or not it actually works.

In another thread, I've been discussing fixing a piping leak in an old Tiger River Bengal spa. Before I turn this over to the pros and pay 100/hr to have them look at it, I wanted to know if these products advertised as "Able to seal any leak up to 1/8" " actually work, or are they junk? Thanks

Not sure on how to remove the cabinet as it was before my time, but it is anywhere between 1992-96. Terminator Let it leak until it stops, see what is at the water level for jets in that area. Drain, flip it on it's side and dig out the wet foam from the bottom to that or those jets, repair leak, re-foam tip back down and refill. 1-3 hours not counting drain and refill time. Thanks for the responses. Roger- I take it this is a full-foam tub then? I did notice when we moved it, the bottom was all foam, with 2x4 runners http://farm2.static.flickr.com/1413/139418...d6114e214_b.jpg Also, I got some photos of the spa before we drained and moved it, after the tub had been sitting unattended for a few months, and I think this might be a shot of the leaky jet, yes? That is the corner with the drip, now... http://farm2.static.flickr.com/1422/141011...4381c7ebe_o.jpg Once I carve out the wet foam and make the repair, what do I use to replace the foam, "Great Stuff"? Or some other brand of the sprayed-in foaming styrofoam insulation? Thanks again! Mike I would say you found the culprit by the photo. Yes gret stuff will work fine a little denser is better but the big 2 part kits at Grainger are more than you need and very expensive. Following the wet foam will be easy. Hey Roger, I followed your instructions, and tunneled in to the area of the leaky jet. Here it is- http://farm2.static.flickr.com/1031/141931...5cf79c741_b.jpg I have a question: The pipe, jet and everything else is encased in a rigid epoxy-like layer of foam, about a half-inch thick. I chipped away at it for a while, and realised this was getting nowhere. I'm assuming I need to get down to the bare fitting to repair/replace whatever is actually leaking. How do i get this rock-hard stuff off, and how do I actually remove the jet if it needs replacing? Thanks, so far your info has been right on target! Mike The local spa company indicated it would be 105.00 for the first hour, plus parts, to fix this. That's starting to sond like a bargain, instead of hassling with this rigid foam. Ay tips on getting through this and down to the leaky pipe/fitting will be appreciated!

Not sure on how to remove the cabinet as it was before my time, but it is anywhere between 1992-96. Terminator Let it leak until it stops, see what is at the water level for jets in that area. Drain, flip it on it's side and dig out the wet foam from the bottom to that or those jets, repair leak, re-foam tip back down and refill. 1-3 hours not counting drain and refill time. Thanks for the responses. Roger- I take it this is a full-foam tub then? I did notice when we moved it, the bottom was all foam, with 2x4 runners http://farm2.static.flickr.com/1413/139418...d6114e214_b.jpg Also, I got some photos of the spa before we drained and moved it, after the tub had been sitting unattended for a few months, and I think this might be a shot of the leaky jet, yes? That is the corner with the drip, now... http://farm2.static.flickr.com/1422/141011...4381c7ebe_o.jpg Once I carve out the wet foam and make the repair, what do I use to replace the foam, "Great Stuff"? Or some other brand of the sprayed-in foaming styrofoam insulation? Thanks again! Mike I would say you found the culprit by the photo. Yes gret stuff will work fine a little denser is better but the big 2 part kits at Grainger are more than you need and very expensive. Following the wet foam will be easy. Hey Roger, I followed your instructions, and tunneled in to the area of the leaky jet. Here it is- http://farm2.static.flickr.com/1031/141931...5cf79c741_b.jpg I have a question: The pipe, jet and everything else is encased in a rigid epoxy-like layer of foam, about a half-inch thick. I chipped away at it for a while, and realised this was getting nowhere. I'm assuming I need to get down to the bare fitting to repair/replace whatever is actually leaking. How do i get this rock-hard stuff off, and how do I actually remove the jet if it needs replacing? Thanks, so far your info has been right on target! Mike

Not sure on how to remove the cabinet as it was before my time, but it is anywhere between 1992-96. Terminator Let it leak until it stops, see what is at the water level for jets in that area. Drain, flip it on it's side and dig out the wet foam from the bottom to that or those jets, repair leak, re-foam tip back down and refill. 1-3 hours not counting drain and refill time. Thanks for the responses. Roger- I take it this is a full-foam tub then? I did notice when we moved it, the bottom was all foam, with 2x4 runners http://farm2.static.flickr.com/1413/139418...d6114e214_b.jpg Also, I got some photos of the spa before we drained and moved it, after the tub had been sitting unattended for a few months, and I think this might be a shot of the leaky jet, yes? That is the corner with the drip, now... http://farm2.static.flickr.com/1422/141011...4381c7ebe_o.jpg Once I carve out the wet foam and make the repair, what do I use to replace the foam, "Great Stuff"? Or some other brand of the sprayed-in foaming styrofoam insulation? Thanks again! Mike

I just picked up an older Tiger River Bengal for a song. ($200.00) images available here- http://farm2.static.flickr.com/1105/139332...fdec76a3d_b.jpg http://farm2.static.flickr.com/1008/139332...212372980_b.jpg http://farm2.static.flickr.com/1085/117691...9914c8ebf_b.jpg It had sat half full at a friend's vacant house for several months. I filled it a day before the electric was ready, and there was no indication of a leak. However, once it heated up, it developed a leak in the back left corner when facing the control panel. I have pulled the access cover and there are no leaks in that area. My question is, how do I remove the panels around the side and back of this spa? There are no visible screws. Also, can anybody give a guess on how old this spa is? Thanks for any help!