Everett2008

Recently I made a post about the "FLO" error message on my 1997 Cal Spas Premier Series 3. The following suggestion was made by ps558: So my questions: Where is the switch? Is there more than one? If more than one, how do I recognize the bad one? Is it a specialized part, or are they the same on most spas? Can I do it myself? Where can I find one? Thanks for the help!

I own a 1997 Cal Spas Premier Series 3 "The Tropical", and it's giving me an error message that says "FLO". According to the manual, when the "FLO" message is present and not blinking, "A pressure switch has malfunctioned-- call your local service center" When I turn off the power and turn it back on again, the tub works fine for 24-48 hours, then the message comes up again. I also drained the tub, and after I refilled it, it worked fine for a couple weeks before the "FLO" message came up again. So, do you really think it's a pressure switch? Is there something I can do on my own? Has anybody else seen this problem? Thanks!

I recently bought a used spa and subsequently bought a kit of chemicals that claimed to have all the stuff I'd ever need for the next three months (cost $100). Of the different things in the kit, what can I use as a homemade substitute for each of the chemicals to perform the same task (e.g., baking soda works for raising pH)? Are there some that I won't even need? Do I really need to use as much as they say I do? The following are the chemicals that came in the kit: pH up pH down Hardness increaser Water clarifier (emulsifier) non-chlorine/non-bromine shock de-foamer scale and stain preventer (for use during fill-up) cartridge cleaner granular chlorine Mineral purifier (which came in the form on a narrow cylinder that's supposed to go inside the filter) Thanks for the help!

I think I'll buy a Cal Spa Tropical (7' x 7') from a person I know for a few hundred dollars. Since I'm saving a ton, and since I know it may eventually need a little repair work, I want to know what can be done and roughly what I would expect to pay to have it done. Here are some things I COULD get. What do you think each would cost? Do you think that certain things are wasteful? What add-ons have you enjoyed? Here's my list so far... feel free to add to it: New motor(s) New Ozonator Refinish wood siding New heating element Additional jets (can this be done?) Internal tub lighting/LED Lighting kit External tub lighting TV Sound system Stairs High-end cover (is a middle-of-the-road cover just as good?) Cover lift Drink tray Anything else?

The fellow selling the tub doesn't use it since his kids went to college. I know him, and I know he wouldn't sell me junk. I saw the tub running, and everything seems to be in order. For $400 (which includes delivery), I figured I can't get hurt too bad. That does lead me to a new question (since I'm potentially saving so much money) which I will start a new thread for... how much would it cost to "Pimp My Tub"?

I know a guy who is willing to sell his Cal Spas Tropical (7' x 7') to me and deliver it. It's 10 years old and runs well. I looked "under the hood" and I saw a box that said something like "Calzonator" or something to that effect. Is that an ozone machine? If so, should I get a new one, given the age of tub? Are there any other pieces and parts that I should replace because of the age of the tub? Thanks for your thoughts!

Since I wouldn't be able to heat and jet at the same time, should I worry about heat loss during a 30-45 minute soak if the outdoor temperature is around 30-40 degrees? Should I expect to lose 1 degree or 10? (Assumes tub is decently insulated) Thanks!

I'm in the market for my first tub, and I visited a tub store the other day. The Tiger River Bengal makes a 110 volt and a 220 volt. If I don't care about heating and jetting at the same time, it seems as if I really don't need to incur the extra expense of running about 80 feet of wire for the 220v. I'm under the impression that if I have a standard 110v outlet nearby that an electrician can quickly and inexpensively make that work. I looked at a similar Bullfrog (451) that only comes in 220v but cost about $700 less. So, here are my questions: 1) Since I usually would be the only person in the tub, can I shut off other jets to compensate for the smaller motor? 2) How much less would I expect to pay the electrician to do a 110v from an outlet 15 feet away versus 220v from my box that's 80 feet away (assuming no obstacles or irregularities)? 3) Is $6500 a "great deal" on a close-out floor model for a Bengal? The "free" add-ons include cover, cover lifter, chemicals, transport and placement. 4) If I go the 110v route does that take up my one outdoor outlet near the tub, or does the electrician just put another one near it? 5) Will the electrical bills be much different with 110v compared to 220v? Thanks for the help on any and all of the questions!

I'm in the market for a tub, probably about a 7' by 7' model. The only way to get the tub to where I want it is through a narrow (4-5 foot wide) passageway between large trees, shrubs, etc. If the tub is flipped on its side, it should be fine. Is it acceptable to move a tub on its side? My house is on a slope and has a lot of trees so that crane delivery would not be possible. Also, how much packaging is used around tubs (i.e., if a tub is 39" tall, how tall is the box it comes in)?